#include // Backlight (pin 10) connected to +3.3 V // MISO (pin 9) connected to PA4 (SSI0Rx) // SCK (pin 8) connected to PA2 (SSI0Clk) // MOSI (pin 7) connected to PA5 (SSI0Tx) // TFT_CS (pin 6) connected to PA3 (SSI0Fss) <- GPIO high to disable TFT // CARD_CS (pin 5) connected to PB0 GPIO output // Data/Command (pin 4) connected to PA6 (GPIO)<- GPIO low not using TFT // RESET (pin 3) connected to PA7 (GPIO)<- GPIO high to disable TFT // VCC (pin 2) connected to +3.3 V // Gnd (pin 1) connected to ground typedef enum { STA_OK = 0, STA_NOINIT = 1, // Drive not initialized STA_NODISK = 2, // No medium in the drive STA_PROTECT = 4, // Write protected } DSTATUS; // Results of Disk Functions typedef enum { RES_OK = 0, // 0: Successful RES_ERROR, // 1: R/W Error RES_WRPRT, // 2: Write Protected RES_NOTRDY, // 3: Not Ready RES_PARERR // 4: Invalid Parameter } DRESULT; // Initialize the interface to the SD card // Since this program initializes the disk, it must run with the disk periodic // task operating. DSTATUS eDisk_Init(); // Checks the status of the card DSTATUS eDisk_Status(); // Read data from the SD card // count: number of sectors to read (1..255) DRESULT eDisk_Read(uint8_t* buff, uint32_t sector, uint8_t count); // Read 512-byte block from SD card DRESULT eDisk_ReadBlock(void* buff, uint32_t sector); // Write bytes to SD card. // count: number of sectors to write (1..255) DRESULT eDisk_Write(const uint8_t* buff, uint32_t sector, uint8_t count); // Write one block to the SD card (read to RAM) DRESULT eDisk_WriteBlock(const void* buff, uint32_t sector); void SSI0_Init(unsigned long CPSDVSR); // This implements timeout functions (should be called every ms) void disk_timerproc(void); // General purpose function for all disk I/O DRESULT disk_ioctl(uint8_t cmd, void* buff); // Command codes for disk_ioctrl fucntion: // Generic command #define CTRL_SYNC \ 0 // Complete pending write process (needed at _FS_READONLY == 0) #define GET_SECTOR_COUNT 1 // Get media size (needed at _USE_MKFS == 1) #define GET_SECTOR_SIZE 2 // Get sector size (needed at _MAX_SS != _MIN_SS) #define GET_BLOCK_SIZE 3 // Get erase block size (needed at _USE_MKFS == 1) #define CTRL_TRIM \ 4 // Inform device that the data on the block of sectors is no longer used // Generic command #define CTRL_FORMAT 5 // Create physical format on the media #define CTRL_POWER_IDLE 6 // Put the device idle state #define CTRL_POWER_OFF 7 // Put the device off state #define CTRL_LOCK 8 // Lock media removal #define CTRL_UNLOCK 9 // Unlock media removal #define CTRL_EJECT 10 // Eject media // MMC/SDC specific command #define MMC_GET_TYPE 50 // Get card type #define MMC_GET_CSD 51 // Get CSD #define MMC_GET_CID 52 // Get CID #define MMC_GET_OCR 53 // Get OCR #define MMC_GET_SDSTAT 54 // Get SD status // ATA/CF specific command #define ATA_GET_REV 60 // Get F/W revision #define ATA_GET_MODEL 61 // Get model name #define ATA_GET_SN 62 // Get serial number // MMC card type flags (MMC_GET_TYPE) #define CT_MMC 0x01 // MMC ver 3 #define CT_SD1 0x02 // SD ver 1 #define CT_SD2 0x04 // SD ver 2 #define CT_SDC (CT_SD1 | CT_SD2) // SD #define CT_BLOCK 0x08 // Block addressing