+/rtos
git clone https://git.julia.blue/+/rtos
83915e3
master
1//***************************************************************************** 2// 3// usbulpi.c - ULPI access functions. 4// 5// Copyright (c) 2013-2017 Texas Instruments Incorporated. All rights reserved. 6// Software License Agreement 7// 8// Texas Instruments (TI) is supplying this software for use solely and 9// exclusively on TI's microcontroller products. The software is owned by 10// TI and/or its suppliers, and is protected under applicable copyright 11// laws. You may not combine this software with "viral" open-source 12// software in order to form a larger program. 13// 14// THIS SOFTWARE IS PROVIDED "AS IS" AND WITH ALL FAULTS. 15// NO WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT 16// NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR 17// A PARTICULAR PURPOSE APPLY TO THIS SOFTWARE. TI SHALL NOT, UNDER ANY 18// CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL 19// DAMAGES, FOR ANY REASON WHATSOEVER. 20// 21// This is part of revision 2.1.4.178 of the Tiva USB Library. 22// 23//***************************************************************************** 24#include "usblib/usbulpi.h" 25#include "tivaware/hw_types.h" 26#include "tivaware/usb.h" 27#include <stdbool.h> 28#include <stdint.h> 29 30//***************************************************************************** 31// 32// Hardware ULPI registers. 33// 34//***************************************************************************** 35#define ULPI_FCTL 0x04 36#define ULPI_FCTL_SET 0x05 37#define ULPI_FCTL_CLEAR 0x06 38#define ULPI_ICTL 0x07 39#define ULPI_ICTL_SET 0x08 40#define ULPI_ICTL_CLEAR 0x09 41#define ULPI_OTGCTL 0x0A 42#define ULPI_OTGCTL_SET 0x0B 43#define ULPI_OTGCTL_CLEAR 0x0C 44 45//***************************************************************************** 46// 47// The following are defines for the bit fields in the ULPI_FCTL register. 48// 49//***************************************************************************** 50#define ULPI_FCTL_XCVR_M 0x03 51#define ULPI_FCTL_XCVR_HS 0x00 52#define ULPI_FCTL_XCVR_FS 0x01 53#define ULPI_FCTL_XCVR_LS 0x02 54#define ULPI_FCTL_XCVR_FSLS 0x03 55#define ULPI_FCTL_TERMSEL 0x04 56#define ULPI_FCTL_OPMODE_M 0x18 57#define ULPI_FCTL_OPMODE_NORM 0x00 58#define ULPI_FCTL_OPMODE_NODRV 0x08 59#define ULPI_FCTL_OPMODE_NONRZI 0x10 60#define ULPI_FCTL_OPMODE_DISAUTO 0x18 61#define ULPI_FCTL_OPMODE_RESET 0x20 62#define ULPI_FCTL_OPMODE_SUSPEND 0x40 63 64//***************************************************************************** 65// 66// The following are defines for the bit fields in the ULPI_ICTL register. 67// 68//***************************************************************************** 69#define ULPI_ICTL_SER6PIN 0x01 70#define ULPI_ICTL_SER3PIN 0x02 71#define ULPI_ICTL_AUTORESUME 0x10 72#define ULPI_ICTL_INDINV 0x20 73#define ULPI_ICTL_INDPASSTHRU 0x40 74#define ULPI_ICTL_PROTDIS 0x80 75 76//***************************************************************************** 77// 78// The following are defines for the bit fields in the ULPI_OTGCTL register. 79// 80//***************************************************************************** 81#define ULPI_OTGCTL_ID_EN 0x01 82#define ULPI_OTGCTL_DPPD_EN 0x02 83#define ULPI_OTGCTL_DMPD_EN 0x04 84#define ULPI_OTGCTL_DISCHRG_VBUS 0x08 85#define ULPI_OTGCTL_CHRG_VBUS 0x10 86#define ULPI_OTGCTL_VBUSINT_EN 0x20 87#define ULPI_OTGCTL_VBUSEXT_EN 0x40 88#define ULPI_OTGCTL_VBUSEXT_IND 0x80 89 90//***************************************************************************** 91// 92//! Sets the configuration of an external USB Phy. 93//! 94//! \param ui32Base specifies the USB module base address. 95//! \param ui32Config specifies the configuration options for the external Phy. 96//! 97//! This function sets the configuration options for an externally connected 98//! USB Phy that is connected using the ULPI interface. The \e ui32Config 99//! parameter holds all of the configuration options defined by the 100//! \b UPLI_CFG_ values. The values are grouped as follows: 101//! 102//! Connection speed, using one of the following: 103//! - \b UPLI_CFG_HS enables high speed operation. 104//! - \b UPLI_CFG_FS enables full speed operation. 105//! - \b UPLI_CFG_HS enables low speed operation. 106//! 107//! Any of the following can be included: 108//! - \b UPLI_CFG_AUTORESUME enable automatic transmission of resume signaling 109//! from the Phy. 110//! - \b UPLI_CFG_INVVBUSIND inverts the external VBUS indicator if it is 111//! selected. 112//! - \b UPLI_CFG_PASSTHRUIND passes the external VBUS indicator through 113//! without using the Phy's VBUS comparator. 114//! - \b ULPI_CFG_EXTVBUSDRV enables an external VBUS drive source. 115//! - \b ULPI_CFG_EXTVBUSIND enables an external signal for VBUS valid. 116//! 117//! \return None. 118// 119//***************************************************************************** 120void ULPIConfigSet (uint32_t ui32Base ,uint32_t ui32Config ) { 121uint8_t ui8Val ; 122 123ui8Val = USBULPIRegRead (ui32Base ,ULPI_FCTL ); 124ui8Val &= ~(ULPI_FCTL_XCVR_M ); 125ui8Val = ui8Val | (uint8_t )ui32Config ; 126 127USBULPIRegWrite (ui32Base ,ULPI_FCTL ,ui8Val ); 128 129ui8Val = USBULPIRegRead (ui32Base ,ULPI_ICTL ); 130ui8Val &= 131 ~(ULPI_ICTL_AUTORESUME |ULPI_ICTL_INDINV |ULPI_ICTL_INDPASSTHRU ); 132ui8Val = ui8Val | (uint8_t )((ui32Config >>8 )& 0xff ); 133 134USBULPIRegWrite (ui32Base ,ULPI_ICTL ,ui8Val ); 135 136ui8Val = USBULPIRegRead (ui32Base ,ULPI_OTGCTL ); 137ui8Val &= ~(ULPI_OTGCTL_VBUSINT_EN |ULPI_OTGCTL_VBUSEXT_EN | 138ULPI_OTGCTL_VBUSEXT_IND ); 139ui8Val = ui8Val | (uint8_t )((ui32Config >>16 )& 0xff ); 140 141USBULPIRegWrite (ui32Base ,ULPI_OTGCTL ,ui8Val ); 142} 143 144//***************************************************************************** 145// 146//! Enables or disables power to the external USB Phy. 147//! 148//! \param ui32Base specifies the USB module base address. 149//! \param bEnable specifies if the Phy is fully powered or in suspend mode. 150//! 151//! This function sets the current power configuration for the external ULPI 152//! connected Phy. When \e bEnable is \b true the Phy is fully powered and 153//! when \b false the USB Phy is in suspend mode. 154//! 155//! \return None. 156// 157//***************************************************************************** 158void ULPIPowerTransceiver (uint32_t ui32Base ,bool bEnable ) { 159if (bEnable ) { 160USBULPIRegWrite (ui32Base ,ULPI_FCTL_CLEAR ,ULPI_FCTL_OPMODE_SUSPEND ); 161 }else { 162USBULPIRegWrite (ui32Base ,ULPI_FCTL_SET ,ULPI_FCTL_OPMODE_SUSPEND ); 163 } 164}