/*************************************************** This is a library for the Adafruit 1.8" SPI display. This library works with the Adafruit 1.8" TFT Breakout w/SD card ----> http://www.adafruit.com/products/358 as well as Adafruit raw 1.8" TFT display ----> http://www.adafruit.com/products/618 Check out the links above for our tutorials and wiring diagrams These displays use SPI to communicate, 4 or 5 pins are required to interface (RST is optional) Adafruit invests time and resources providing this open source code, please support Adafruit and open-source hardware by purchasing products from Adafruit! Written by Limor Fried/Ladyada for Adafruit Industries. MIT license, all text above must be included in any redistribution ****************************************************/ // ST7735.cpp // Runs on LM4F120/TM4C123 // Low level drivers for the ST7735 160x128 LCD based off of // the file described above. // 16-bit color, 128 wide by 160 high LCD // Daniel Valvano // March 5, 2018 // Augmented 7/17/2014 to have a simple graphics facility // Tested with LaunchPadDLL.dll simulator 9/2/2014 // Modified for use of CS (simultaneous with other SPI slaves) 3/28/2016 /* This example accompanies the book "Embedded Systems: Real Time Interfacing to ARM Cortex M Microcontrollers", ISBN: 978-1463590154, Jonathan Valvano, copyright (c) 2017 Copyright 2018 by Jonathan W. Valvano, valvano@mail.utexas.edu You may use, edit, run or distribute this file as long as the above copyright notice remains THIS SOFTWARE IS PROVIDED "AS IS". NO WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE APPLY TO THIS SOFTWARE. VALVANO SHALL NOT, IN ANY CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, FOR ANY REASON WHATSOEVER. For more information about my classes, my research, and my books, see http://users.ece.utexas.edu/~valvano/ */ // hardware connections // **********ST7735 TFT and SDC******************* // ST7735 // Backlight (pin 10) connected to +3.3 V // MISO (pin 9) unconnected // SCK (pin 8) connected to PA2 (SSI0Clk) // MOSI (pin 7) connected to PA5 (SSI0Tx) // TFT_CS (pin 6) connected to PA3 (SSI0Fss) // CARD_CS (pin 5) unconnected // Data/Command (pin 4) connected to PA6 (GPIO), high for data, low for command // RESET (pin 3) connected to PA7 (GPIO) // VCC (pin 2) connected to +3.3 V // Gnd (pin 1) connected to ground // **********wide.hk ST7735R with ADXL345 accelerometer ******************* // Silkscreen Label (SDC side up; LCD side down) - Connection // VCC - +3.3 V // GND - Ground // !SCL - PA2 Sclk SPI clock from microcontroller to TFT or SDC // !SDA - PA5 MOSI SPI data from microcontroller to TFT or SDC // DC - PA6 TFT data/command // RES - PA7 TFT reset // CS - PA3 TFT_CS, active low to enable TFT // *CS - (NC) SDC_CS, active low to enable SDC // MISO - (NC) MISO SPI data from SDC to microcontroller // SDA � (NC) I2C data for ADXL345 accelerometer // SCL � (NC) I2C clock for ADXL345 accelerometer // SDO � (NC) I2C alternate address for ADXL345 accelerometer // Backlight + - Light, backlight connected to +3.3 V // **********wide.hk ST7735R with ADXL335 accelerometer ******************* // Silkscreen Label (SDC side up; LCD side down) - Connection // VCC - +3.3 V // GND - Ground // !SCL - PA2 Sclk SPI clock from microcontroller to TFT or SDC // !SDA - PA5 MOSI SPI data from microcontroller to TFT or SDC // DC - PA6 TFT data/command // RES - PA7 TFT reset // CS - PA3 TFT_CS, active low to enable TFT // *CS - (NC) SDC_CS, active low to enable SDC // MISO - (NC) MISO SPI data from SDC to microcontroller // X� (NC) analog input X-axis from ADXL335 accelerometer // Y� (NC) analog input Y-axis from ADXL335 accelerometer // Z� (NC) analog input Z-axis from ADXL335 accelerometer // Backlight + - Light, backlight connected to +3.3 V // **********HiLetgo ST7735 TFT and SDC (SDC not tested)******************* // ST7735 // LED- (pin 16) TFT, connected to ground // LED+ (pin 15) TFT, connected to +3.3 V // SD_CS (pin 14) SDC, chip select // MOSI (pin 13) SDC, MOSI // MISO (pin 12) SDC, MISO // SCK (pin 11) SDC, serial clock // CS (pin 10) TFT, PA3 (SSI0Fss) // SCL (pin 9) TFT, SCK PA2 (SSI0Clk) // SDA (pin 8) TFT, MOSI PA5 (SSI0Tx) // A0 (pin 7) TFT, Data/Command PA6 (GPIO), high for data, low for command // RESET (pin 6) TFT, to PA7 (GPIO) // NC (pins 3,4,5) not connected // VCC (pin 2) connected to +3.3 V // GND (pin 1) connected to ground //#include #include //#include #include "../inc/ST7735.h" #include "../inc/tm4c123gh6pm.h" #define SDC_CS_PB0 0 #define SDC_CS_PD7 1 // 16 rows (0 to 15) and 21 characters (0 to 20) // Requires (11 + size*size*6*8) bytes of transmission for each character uint32_t StX=0; // position along the horizonal axis 0 to 20 uint32_t StY=0; // position along the vertical axis 0 to 15 uint16_t StTextColor = ST7735_YELLOW; #define ST7735_NOP 0x00 #define ST7735_SWRESET 0x01 #define ST7735_RDDID 0x04 #define ST7735_RDDST 0x09 #define ST7735_SLPIN 0x10 #define ST7735_SLPOUT 0x11 #define ST7735_PTLON 0x12 #define ST7735_NORON 0x13 #define ST7735_INVOFF 0x20 #define ST7735_INVON 0x21 #define ST7735_DISPOFF 0x28 #define ST7735_DISPON 0x29 #define ST7735_CASET 0x2A #define ST7735_RASET 0x2B #define ST7735_RAMWR 0x2C #define ST7735_RAMRD 0x2E #define ST7735_PTLAR 0x30 #define ST7735_COLMOD 0x3A #define ST7735_MADCTL 0x36 #define ST7735_FRMCTR1 0xB1 #define ST7735_FRMCTR2 0xB2 #define ST7735_FRMCTR3 0xB3 #define ST7735_INVCTR 0xB4 #define ST7735_DISSET5 0xB6 #define ST7735_PWCTR1 0xC0 #define ST7735_PWCTR2 0xC1 #define ST7735_PWCTR3 0xC2 #define ST7735_PWCTR4 0xC3 #define ST7735_PWCTR5 0xC4 #define ST7735_VMCTR1 0xC5 #define ST7735_RDID1 0xDA #define ST7735_RDID2 0xDB #define ST7735_RDID3 0xDC #define ST7735_RDID4 0xDD #define ST7735_PWCTR6 0xFC #define ST7735_GMCTRP1 0xE0 #define ST7735_GMCTRN1 0xE1 #define TFT_CS (*((volatile uint32_t *)0x40004020)) #define TFT_CS_LOW 0 // CS normally controlled by hardware #define TFT_CS_HIGH 0x08 #if SDC_CS_PD7 // PD7 output used for SDC CS #define SDC_CS (*((volatile uint32_t *)0x40007200)) #define SDC_CS_LOW 0 // CS controlled by software #define SDC_CS_HIGH 0x80 void SDC_CS_Init(void){ SYSCTL_RCGCGPIO_R |= 0x08; // activate clock for Port D while((SYSCTL_PRGPIO_R&0x08) == 0){}; // allow time for clock to stabilize GPIO_PORTD_LOCK_R = 0x4C4F434B; // unlock GPIO Port D GPIO_PORTD_CR_R = 0xFF; // allow changes to PD7-0 // only PD7 needs to be unlocked, other bits can't be locked GPIO_PORTD_DIR_R |= 0x80; // make PD7 out GPIO_PORTD_AFSEL_R &= ~0x80; // disable alt funct on PD7 GPIO_PORTD_DR4R_R |= 0x80; // 4mA drive on outputs GPIO_PORTD_PUR_R |= 0x80; // enable weak pullup on PD7 GPIO_PORTD_DEN_R |= 0x80; // enable digital I/O on PD7 // configure PD7 as GPIO GPIO_PORTD_PCTL_R = (GPIO_PORTD_PCTL_R&0x0FFFFFFF)+0x00000000; GPIO_PORTD_AMSEL_R &= ~0x80; // disable analog functionality on PD7 SDC_CS = SDC_CS_HIGH; } #endif // PB0 output used for SDC CS #if SDC_CS_PB0 #define SDC_CS (*((volatile uint32_t *)0x40005004)) #define SDC_CS_LOW 0 // CS controlled by software #define SDC_CS_HIGH 0x01 void SDC_CS_Init(void){ SYSCTL_RCGCGPIO_R |= 0x02; // activate clock for Port B while((SYSCTL_PRGPIO_R&0x02) == 0){}; // allow time for clock to stabilize GPIO_PORTB_DIR_R |= 0x01; // make PB0 out GPIO_PORTB_AFSEL_R &= ~0x01; // disable alt funct on PB0 GPIO_PORTB_DR4R_R |= 0x01; // 4mA drive on outputs GPIO_PORTB_PUR_R |= 0x01; // enable weak pullup on PB0 GPIO_PORTB_DEN_R |= 0x01; // enable digital I/O on PB0 // configure PB0 as GPIO GPIO_PORTB_PCTL_R = (GPIO_PORTB_PCTL_R&0xFFFFFFF0)+0x00000000; GPIO_PORTB_AMSEL_R &= ~0x01; // disable analog functionality on PB0 SDC_CS = SDC_CS_HIGH; } #endif #define DC (*((volatile uint32_t *)0x40004100)) #define DC_COMMAND 0 #define DC_DATA 0x40 #define RESET (*((volatile uint32_t *)0x40004200)) #define RESET_LOW 0 #define RESET_HIGH 0x80 #define SSI_CR0_SCR_M 0x0000FF00 // SSI Serial Clock Rate #define SSI_CR0_SPH 0x00000080 // SSI Serial Clock Phase #define SSI_CR0_SPO 0x00000040 // SSI Serial Clock Polarity #define SSI_CR0_FRF_M 0x00000030 // SSI Frame Format Select #define SSI_CR0_FRF_MOTO 0x00000000 // Freescale SPI Frame Format #define SSI_CR0_DSS_M 0x0000000F // SSI Data Size Select #define SSI_CR0_DSS_8 0x00000007 // 8-bit data #define SSI_CR1_MS 0x00000004 // SSI Master/Slave Select #define SSI_CR1_SSE 0x00000002 // SSI Synchronous Serial Port // Enable #define SSI_SR_BSY 0x00000010 // SSI Busy Bit #define SSI_SR_TNF 0x00000002 // SSI Transmit FIFO Not Full #define SSI_CPSR_CPSDVSR_M 0x000000FF // SSI Clock Prescale Divisor #define SSI_CC_CS_M 0x0000000F // SSI Baud Clock Source #define SSI_CC_CS_SYSPLL 0x00000000 // Either the system clock (if the // PLL bypass is in effect) or the // PLL output (default) #define SYSCTL_RCGC1_SSI0 0x00000010 // SSI0 Clock Gating Control #define SYSCTL_RCGC2_GPIOA 0x00000001 // port A Clock Gating Control #define ST7735_TFTWIDTH 128 #define ST7735_TFTHEIGHT 160 #define ST7735_NOP 0x00 #define ST7735_SWRESET 0x01 #define ST7735_RDDID 0x04 #define ST7735_RDDST 0x09 #define ST7735_SLPIN 0x10 #define ST7735_SLPOUT 0x11 #define ST7735_PTLON 0x12 #define ST7735_NORON 0x13 #define ST7735_INVOFF 0x20 #define ST7735_INVON 0x21 #define ST7735_DISPOFF 0x28 #define ST7735_DISPON 0x29 #define ST7735_CASET 0x2A #define ST7735_RASET 0x2B #define ST7735_RAMWR 0x2C #define ST7735_RAMRD 0x2E #define ST7735_PTLAR 0x30 #define ST7735_COLMOD 0x3A #define ST7735_MADCTL 0x36 #define ST7735_FRMCTR1 0xB1 #define ST7735_FRMCTR2 0xB2 #define ST7735_FRMCTR3 0xB3 #define ST7735_INVCTR 0xB4 #define ST7735_DISSET5 0xB6 #define ST7735_PWCTR1 0xC0 #define ST7735_PWCTR2 0xC1 #define ST7735_PWCTR3 0xC2 #define ST7735_PWCTR4 0xC3 #define ST7735_PWCTR5 0xC4 #define ST7735_VMCTR1 0xC5 #define ST7735_RDID1 0xDA #define ST7735_RDID2 0xDB #define ST7735_RDID3 0xDC #define ST7735_RDID4 0xDD #define ST7735_PWCTR6 0xFC #define ST7735_GMCTRP1 0xE0 #define ST7735_GMCTRN1 0xE1 // standard ascii 5x7 font // originally from glcdfont.c from Adafruit project static const uint8_t Font[] = { 0x00, 0x00, 0x00, 0x00, 0x00, 0x3E, 0x5B, 0x4F, 0x5B, 0x3E, 0x3E, 0x6B, 0x4F, 0x6B, 0x3E, 0x1C, 0x3E, 0x7C, 0x3E, 0x1C, 0x18, 0x3C, 0x7E, 0x3C, 0x18, 0x1C, 0x57, 0x7D, 0x57, 0x1C, 0x1C, 0x5E, 0x7F, 0x5E, 0x1C, 0x00, 0x18, 0x3C, 0x18, 0x00, 0xFF, 0xE7, 0xC3, 0xE7, 0xFF, 0x00, 0x18, 0x24, 0x18, 0x00, 0xFF, 0xE7, 0xDB, 0xE7, 0xFF, 0x30, 0x48, 0x3A, 0x06, 0x0E, 0x26, 0x29, 0x79, 0x29, 0x26, 0x40, 0x7F, 0x05, 0x05, 0x07, 0x40, 0x7F, 0x05, 0x25, 0x3F, 0x5A, 0x3C, 0xE7, 0x3C, 0x5A, 0x7F, 0x3E, 0x1C, 0x1C, 0x08, 0x08, 0x1C, 0x1C, 0x3E, 0x7F, 0x14, 0x22, 0x7F, 0x22, 0x14, 0x5F, 0x5F, 0x00, 0x5F, 0x5F, 0x06, 0x09, 0x7F, 0x01, 0x7F, 0x00, 0x66, 0x89, 0x95, 0x6A, 0x60, 0x60, 0x60, 0x60, 0x60, 0x94, 0xA2, 0xFF, 0xA2, 0x94, 0x08, 0x04, 0x7E, 0x04, 0x08, 0x10, 0x20, 0x7E, 0x20, 0x10, 0x08, 0x08, 0x2A, 0x1C, 0x08, 0x08, 0x1C, 0x2A, 0x08, 0x08, 0x1E, 0x10, 0x10, 0x10, 0x10, 0x0C, 0x1E, 0x0C, 0x1E, 0x0C, 0x30, 0x38, 0x3E, 0x38, 0x30, 0x06, 0x0E, 0x3E, 0x0E, 0x06, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x5F, 0x00, 0x00, 0x00, 0x07, 0x00, 0x07, 0x00, 0x14, 0x7F, 0x14, 0x7F, 0x14, 0x24, 0x2A, 0x7F, 0x2A, 0x12, 0x23, 0x13, 0x08, 0x64, 0x62, 0x36, 0x49, 0x56, 0x20, 0x50, 0x00, 0x08, 0x07, 0x03, 0x00, 0x00, 0x1C, 0x22, 0x41, 0x00, 0x00, 0x41, 0x22, 0x1C, 0x00, 0x2A, 0x1C, 0x7F, 0x1C, 0x2A, 0x08, 0x08, 0x3E, 0x08, 0x08, 0x00, 0x80, 0x70, 0x30, 0x00, 0x08, 0x08, 0x08, 0x08, 0x08, 0x00, 0x00, 0x60, 0x60, 0x00, 0x20, 0x10, 0x08, 0x04, 0x02, 0x3E, 0x51, 0x49, 0x45, 0x3E, // 0 0x00, 0x42, 0x7F, 0x40, 0x00, // 1 0x72, 0x49, 0x49, 0x49, 0x46, // 2 0x21, 0x41, 0x49, 0x4D, 0x33, // 3 0x18, 0x14, 0x12, 0x7F, 0x10, // 4 0x27, 0x45, 0x45, 0x45, 0x39, // 5 0x3C, 0x4A, 0x49, 0x49, 0x31, // 6 0x41, 0x21, 0x11, 0x09, 0x07, // 7 0x36, 0x49, 0x49, 0x49, 0x36, // 8 0x46, 0x49, 0x49, 0x29, 0x1E, // 9 0x00, 0x00, 0x14, 0x00, 0x00, 0x00, 0x40, 0x34, 0x00, 0x00, 0x00, 0x08, 0x14, 0x22, 0x41, 0x14, 0x14, 0x14, 0x14, 0x14, 0x00, 0x41, 0x22, 0x14, 0x08, 0x02, 0x01, 0x59, 0x09, 0x06, 0x3E, 0x41, 0x5D, 0x59, 0x4E, 0x7C, 0x12, 0x11, 0x12, 0x7C, // A 0x7F, 0x49, 0x49, 0x49, 0x36, // B 0x3E, 0x41, 0x41, 0x41, 0x22, // C 0x7F, 0x41, 0x41, 0x41, 0x3E, // D 0x7F, 0x49, 0x49, 0x49, 0x41, // E 0x7F, 0x09, 0x09, 0x09, 0x01, // F 0x3E, 0x41, 0x41, 0x51, 0x73, // G 0x7F, 0x08, 0x08, 0x08, 0x7F, // H 0x00, 0x41, 0x7F, 0x41, 0x00, // I 0x20, 0x40, 0x41, 0x3F, 0x01, // J 0x7F, 0x08, 0x14, 0x22, 0x41, // K 0x7F, 0x40, 0x40, 0x40, 0x40, // L 0x7F, 0x02, 0x1C, 0x02, 0x7F, // M 0x7F, 0x04, 0x08, 0x10, 0x7F, // N 0x3E, 0x41, 0x41, 0x41, 0x3E, // O 0x7F, 0x09, 0x09, 0x09, 0x06, // P 0x3E, 0x41, 0x51, 0x21, 0x5E, // Q 0x7F, 0x09, 0x19, 0x29, 0x46, // R 0x26, 0x49, 0x49, 0x49, 0x32, // S 0x03, 0x01, 0x7F, 0x01, 0x03, // T 0x3F, 0x40, 0x40, 0x40, 0x3F, // U 0x1F, 0x20, 0x40, 0x20, 0x1F, // V 0x3F, 0x40, 0x38, 0x40, 0x3F, // W 0x63, 0x14, 0x08, 0x14, 0x63, // X 0x03, 0x04, 0x78, 0x04, 0x03, // Y 0x61, 0x59, 0x49, 0x4D, 0x43, // Z 0x00, 0x7F, 0x41, 0x41, 0x41, 0x02, 0x04, 0x08, 0x10, 0x20, 0x00, 0x41, 0x41, 0x41, 0x7F, 0x04, 0x02, 0x01, 0x02, 0x04, 0x40, 0x40, 0x40, 0x40, 0x40, 0x00, 0x03, 0x07, 0x08, 0x00, 0x20, 0x54, 0x54, 0x78, 0x40, // a 0x7F, 0x28, 0x44, 0x44, 0x38, // b 0x38, 0x44, 0x44, 0x44, 0x28, // c 0x38, 0x44, 0x44, 0x28, 0x7F, // d 0x38, 0x54, 0x54, 0x54, 0x18, // e 0x00, 0x08, 0x7E, 0x09, 0x02, // f 0x18, 0xA4, 0xA4, 0x9C, 0x78, // g 0x7F, 0x08, 0x04, 0x04, 0x78, // h 0x00, 0x44, 0x7D, 0x40, 0x00, // i 0x20, 0x40, 0x40, 0x3D, 0x00, // j 0x7F, 0x10, 0x28, 0x44, 0x00, // k 0x00, 0x41, 0x7F, 0x40, 0x00, // l 0x7C, 0x04, 0x78, 0x04, 0x78, // m 0x7C, 0x08, 0x04, 0x04, 0x78, // n 0x38, 0x44, 0x44, 0x44, 0x38, // o 0xFC, 0x18, 0x24, 0x24, 0x18, // p 0x18, 0x24, 0x24, 0x18, 0xFC, // q 0x7C, 0x08, 0x04, 0x04, 0x08, // r 0x48, 0x54, 0x54, 0x54, 0x24, // s 0x04, 0x04, 0x3F, 0x44, 0x24, // t 0x3C, 0x40, 0x40, 0x20, 0x7C, // u 0x1C, 0x20, 0x40, 0x20, 0x1C, // v 0x3C, 0x40, 0x30, 0x40, 0x3C, // w 0x44, 0x28, 0x10, 0x28, 0x44, // x 0x4C, 0x90, 0x90, 0x90, 0x7C, // y 0x44, 0x64, 0x54, 0x4C, 0x44, // z 0x00, 0x08, 0x36, 0x41, 0x00, 0x00, 0x00, 0x77, 0x00, 0x00, 0x00, 0x41, 0x36, 0x08, 0x00, 0x02, 0x01, 0x02, 0x04, 0x02, 0x3C, 0x26, 0x23, 0x26, 0x3C, 0x1E, 0xA1, 0xA1, 0x61, 0x12, 0x3A, 0x40, 0x40, 0x20, 0x7A, 0x38, 0x54, 0x54, 0x55, 0x59, 0x21, 0x55, 0x55, 0x79, 0x41, 0x21, 0x54, 0x54, 0x78, 0x41, 0x21, 0x55, 0x54, 0x78, 0x40, 0x20, 0x54, 0x55, 0x79, 0x40, 0x0C, 0x1E, 0x52, 0x72, 0x12, 0x39, 0x55, 0x55, 0x55, 0x59, 0x39, 0x54, 0x54, 0x54, 0x59, 0x39, 0x55, 0x54, 0x54, 0x58, 0x00, 0x00, 0x45, 0x7C, 0x41, 0x00, 0x02, 0x45, 0x7D, 0x42, 0x00, 0x01, 0x45, 0x7C, 0x40, 0xF0, 0x29, 0x24, 0x29, 0xF0, 0xF0, 0x28, 0x25, 0x28, 0xF0, 0x7C, 0x54, 0x55, 0x45, 0x00, 0x20, 0x54, 0x54, 0x7C, 0x54, 0x7C, 0x0A, 0x09, 0x7F, 0x49, 0x32, 0x49, 0x49, 0x49, 0x32, 0x32, 0x48, 0x48, 0x48, 0x32, 0x32, 0x4A, 0x48, 0x48, 0x30, 0x3A, 0x41, 0x41, 0x21, 0x7A, 0x3A, 0x42, 0x40, 0x20, 0x78, 0x00, 0x9D, 0xA0, 0xA0, 0x7D, 0x39, 0x44, 0x44, 0x44, 0x39, 0x3D, 0x40, 0x40, 0x40, 0x3D, 0x3C, 0x24, 0xFF, 0x24, 0x24, 0x48, 0x7E, 0x49, 0x43, 0x66, 0x2B, 0x2F, 0xFC, 0x2F, 0x2B, 0xFF, 0x09, 0x29, 0xF6, 0x20, 0xC0, 0x88, 0x7E, 0x09, 0x03, 0x20, 0x54, 0x54, 0x79, 0x41, 0x00, 0x00, 0x44, 0x7D, 0x41, 0x30, 0x48, 0x48, 0x4A, 0x32, 0x38, 0x40, 0x40, 0x22, 0x7A, 0x00, 0x7A, 0x0A, 0x0A, 0x72, 0x7D, 0x0D, 0x19, 0x31, 0x7D, 0x26, 0x29, 0x29, 0x2F, 0x28, 0x26, 0x29, 0x29, 0x29, 0x26, 0x30, 0x48, 0x4D, 0x40, 0x20, 0x38, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x38, 0x2F, 0x10, 0xC8, 0xAC, 0xBA, 0x2F, 0x10, 0x28, 0x34, 0xFA, 0x00, 0x00, 0x7B, 0x00, 0x00, 0x08, 0x14, 0x2A, 0x14, 0x22, 0x22, 0x14, 0x2A, 0x14, 0x08, 0xAA, 0x00, 0x55, 0x00, 0xAA, 0xAA, 0x55, 0xAA, 0x55, 0xAA, 0x00, 0x00, 0x00, 0xFF, 0x00, 0x10, 0x10, 0x10, 0xFF, 0x00, 0x14, 0x14, 0x14, 0xFF, 0x00, 0x10, 0x10, 0xFF, 0x00, 0xFF, 0x10, 0x10, 0xF0, 0x10, 0xF0, 0x14, 0x14, 0x14, 0xFC, 0x00, 0x14, 0x14, 0xF7, 0x00, 0xFF, 0x00, 0x00, 0xFF, 0x00, 0xFF, 0x14, 0x14, 0xF4, 0x04, 0xFC, 0x14, 0x14, 0x17, 0x10, 0x1F, 0x10, 0x10, 0x1F, 0x10, 0x1F, 0x14, 0x14, 0x14, 0x1F, 0x00, 0x10, 0x10, 0x10, 0xF0, 0x00, 0x00, 0x00, 0x00, 0x1F, 0x10, 0x10, 0x10, 0x10, 0x1F, 0x10, 0x10, 0x10, 0x10, 0xF0, 0x10, 0x00, 0x00, 0x00, 0xFF, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0xFF, 0x10, 0x00, 0x00, 0x00, 0xFF, 0x14, 0x00, 0x00, 0xFF, 0x00, 0xFF, 0x00, 0x00, 0x1F, 0x10, 0x17, 0x00, 0x00, 0xFC, 0x04, 0xF4, 0x14, 0x14, 0x17, 0x10, 0x17, 0x14, 0x14, 0xF4, 0x04, 0xF4, 0x00, 0x00, 0xFF, 0x00, 0xF7, 0x14, 0x14, 0x14, 0x14, 0x14, 0x14, 0x14, 0xF7, 0x00, 0xF7, 0x14, 0x14, 0x14, 0x17, 0x14, 0x10, 0x10, 0x1F, 0x10, 0x1F, 0x14, 0x14, 0x14, 0xF4, 0x14, 0x10, 0x10, 0xF0, 0x10, 0xF0, 0x00, 0x00, 0x1F, 0x10, 0x1F, 0x00, 0x00, 0x00, 0x1F, 0x14, 0x00, 0x00, 0x00, 0xFC, 0x14, 0x00, 0x00, 0xF0, 0x10, 0xF0, 0x10, 0x10, 0xFF, 0x10, 0xFF, 0x14, 0x14, 0x14, 0xFF, 0x14, 0x10, 0x10, 0x10, 0x1F, 0x00, 0x00, 0x00, 0x00, 0xF0, 0x10, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xF0, 0xF0, 0xF0, 0xF0, 0xF0, 0xFF, 0xFF, 0xFF, 0x00, 0x00, 0x00, 0x00, 0x00, 0xFF, 0xFF, 0x0F, 0x0F, 0x0F, 0x0F, 0x0F, 0x38, 0x44, 0x44, 0x38, 0x44, 0x7C, 0x2A, 0x2A, 0x3E, 0x14, 0x7E, 0x02, 0x02, 0x06, 0x06, 0x02, 0x7E, 0x02, 0x7E, 0x02, 0x63, 0x55, 0x49, 0x41, 0x63, 0x38, 0x44, 0x44, 0x3C, 0x04, 0x40, 0x7E, 0x20, 0x1E, 0x20, 0x06, 0x02, 0x7E, 0x02, 0x02, 0x99, 0xA5, 0xE7, 0xA5, 0x99, 0x1C, 0x2A, 0x49, 0x2A, 0x1C, 0x4C, 0x72, 0x01, 0x72, 0x4C, 0x30, 0x4A, 0x4D, 0x4D, 0x30, 0x30, 0x48, 0x78, 0x48, 0x30, 0xBC, 0x62, 0x5A, 0x46, 0x3D, 0x3E, 0x49, 0x49, 0x49, 0x00, 0x7E, 0x01, 0x01, 0x01, 0x7E, 0x2A, 0x2A, 0x2A, 0x2A, 0x2A, 0x44, 0x44, 0x5F, 0x44, 0x44, 0x40, 0x51, 0x4A, 0x44, 0x40, 0x40, 0x44, 0x4A, 0x51, 0x40, 0x00, 0x00, 0xFF, 0x01, 0x03, 0xE0, 0x80, 0xFF, 0x00, 0x00, 0x08, 0x08, 0x6B, 0x6B, 0x08, 0x36, 0x12, 0x36, 0x24, 0x36, 0x06, 0x0F, 0x09, 0x0F, 0x06, 0x00, 0x00, 0x18, 0x18, 0x00, 0x00, 0x00, 0x10, 0x10, 0x00, 0x30, 0x40, 0xFF, 0x01, 0x01, 0x00, 0x1F, 0x01, 0x01, 0x1E, 0x00, 0x19, 0x1D, 0x17, 0x12, 0x00, 0x3C, 0x3C, 0x3C, 0x3C, 0x00, 0x00, 0x00, 0x00, 0x00, }; static uint8_t ColStart, RowStart; // some displays need this changed static uint8_t Rotation; // 0 to 3 static enum initRFlags TabColor; static int16_t _width = ST7735_TFTWIDTH; // this could probably be a constant, except it is used in Adafruit_GFX and depends on image rotation static int16_t _height = ST7735_TFTHEIGHT; // The Data/Command pin must be valid when the eighth bit is // sent. The SSI module has hardware input and output FIFOs // that are 8 locations deep; however, they are not used in // this implementation. Each function first stalls while // waiting for any pending SSI0 transfers to complete. Once // the SSI0 module is idle, it then prepares the Chip Select // pins for the SD card and LCD and the Data/Command pin. // Next it starts transmitting the data or command. Finally // once the hardware is idle again, it sets all chip select // pins high as required by the serial protocol. This is a // significant change from previous implementations of this // function. It is less efficient without the FIFOs, but it // should ensure that the Chip Select and Data/Command pin // statuses all match the byte that is actually being // transmitted. // NOTE: These functions will crash or stall indefinitely if // the SSI0 module is not initialized and enabled. void static writecommand(unsigned char c) { volatile uint32_t response; // wait until SSI0 not busy/transmit FIFO empty while((SSI0_SR_R&SSI_SR_BSY)==SSI_SR_BSY){}; SDC_CS = SDC_CS_HIGH; TFT_CS = TFT_CS_LOW; DC = DC_COMMAND; SSI0_DR_R = c; // data out while((SSI0_SR_R&SSI_SR_RNE)==0){}; // wait until response TFT_CS = TFT_CS_HIGH; response = SSI0_DR_R; // acknowledge response } void static writedata(unsigned char c) { volatile uint32_t response; // wait until SSI0 not busy/transmit FIFO empty while((SSI0_SR_R&SSI_SR_BSY)==SSI_SR_BSY){}; SDC_CS = SDC_CS_HIGH; TFT_CS = TFT_CS_LOW; DC = DC_DATA; SSI0_DR_R = c; // data out while((SSI0_SR_R&SSI_SR_RNE)==0){}; // wait until response TFT_CS = TFT_CS_HIGH; response = SSI0_DR_R; // acknowledge response } void static deselect(void) { // wait until SSI0 not busy/transmit FIFO empty while((SSI0_SR_R&SSI_SR_BSY)==SSI_SR_BSY){}; TFT_CS = TFT_CS_HIGH; } // Subroutine to wait 1 msec // Inputs: None // Outputs: None // Notes: ... void Delay1ms(uint32_t n){uint32_t volatile time; while(n){ time = 72724*2/91; // 1msec, tuned at 80 MHz while(time){ time--; } n--; } } // Rather than a bazillion writecommand() and writedata() calls, screen // initialization commands and arguments are organized in these tables // stored in ROM. The table may look bulky, but that's mostly the // formatting -- storage-wise this is hundreds of bytes more compact // than the equivalent code. Companion function follows. #define DELAY 0x80 static const uint8_t Bcmd[] = { // Initialization commands for 7735B screens 18, // 18 commands in list: ST7735_SWRESET, DELAY, // 1: Software reset, no args, w/delay 50, // 50 ms delay ST7735_SLPOUT , DELAY, // 2: Out of sleep mode, no args, w/delay 255, // 255 = 500 ms delay ST7735_COLMOD , 1+DELAY, // 3: Set color mode, 1 arg + delay: 0x05, // 16-bit color 10, // 10 ms delay ST7735_FRMCTR1, 3+DELAY, // 4: Frame rate control, 3 args + delay: 0x00, // fastest refresh 0x06, // 6 lines front porch 0x03, // 3 lines back porch 10, // 10 ms delay ST7735_MADCTL , 1 , // 5: Memory access ctrl (directions), 1 arg: 0x08, // Row addr/col addr, bottom to top refresh ST7735_DISSET5, 2 , // 6: Display settings #5, 2 args, no delay: 0x15, // 1 clk cycle nonoverlap, 2 cycle gate // rise, 3 cycle osc equalize 0x02, // Fix on VTL ST7735_INVCTR , 1 , // 7: Display inversion control, 1 arg: 0x0, // Line inversion ST7735_PWCTR1 , 2+DELAY, // 8: Power control, 2 args + delay: 0x02, // GVDD = 4.7V 0x70, // 1.0uA 10, // 10 ms delay ST7735_PWCTR2 , 1 , // 9: Power control, 1 arg, no delay: 0x05, // VGH = 14.7V, VGL = -7.35V ST7735_PWCTR3 , 2 , // 10: Power control, 2 args, no delay: 0x01, // Opamp current small 0x02, // Boost frequency ST7735_VMCTR1 , 2+DELAY, // 11: Power control, 2 args + delay: 0x3C, // VCOMH = 4V 0x38, // VCOML = -1.1V 10, // 10 ms delay ST7735_PWCTR6 , 2 , // 12: Power control, 2 args, no delay: 0x11, 0x15, ST7735_GMCTRP1,16 , // 13: Magical unicorn dust, 16 args, no delay: 0x09, 0x16, 0x09, 0x20, // (seriously though, not sure what 0x21, 0x1B, 0x13, 0x19, // these config values represent) 0x17, 0x15, 0x1E, 0x2B, 0x04, 0x05, 0x02, 0x0E, ST7735_GMCTRN1,16+DELAY, // 14: Sparkles and rainbows, 16 args + delay: 0x0B, 0x14, 0x08, 0x1E, // (ditto) 0x22, 0x1D, 0x18, 0x1E, 0x1B, 0x1A, 0x24, 0x2B, 0x06, 0x06, 0x02, 0x0F, 10, // 10 ms delay ST7735_CASET , 4 , // 15: Column addr set, 4 args, no delay: 0x00, 0x02, // XSTART = 2 0x00, 0x81, // XEND = 129 ST7735_RASET , 4 , // 16: Row addr set, 4 args, no delay: 0x00, 0x02, // XSTART = 1 0x00, 0x81, // XEND = 160 ST7735_NORON , DELAY, // 17: Normal display on, no args, w/delay 10, // 10 ms delay ST7735_DISPON , DELAY, // 18: Main screen turn on, no args, w/delay 255 }; // 255 = 500 ms delay static const uint8_t Rcmd1[] = { // Init for 7735R, part 1 (red or green tab) 15, // 15 commands in list: ST7735_SWRESET, DELAY, // 1: Software reset, 0 args, w/delay 150, // 150 ms delay ST7735_SLPOUT , DELAY, // 2: Out of sleep mode, 0 args, w/delay 255, // 500 ms delay ST7735_FRMCTR1, 3 , // 3: Frame rate ctrl - normal mode, 3 args: 0x01, 0x2C, 0x2D, // Rate = fosc/(1x2+40) * (LINE+2C+2D) ST7735_FRMCTR2, 3 , // 4: Frame rate control - idle mode, 3 args: 0x01, 0x2C, 0x2D, // Rate = fosc/(1x2+40) * (LINE+2C+2D) ST7735_FRMCTR3, 6 , // 5: Frame rate ctrl - partial mode, 6 args: 0x01, 0x2C, 0x2D, // Dot inversion mode 0x01, 0x2C, 0x2D, // Line inversion mode ST7735_INVCTR , 1 , // 6: Display inversion ctrl, 1 arg, no delay: 0x07, // No inversion ST7735_PWCTR1 , 3 , // 7: Power control, 3 args, no delay: 0xA2, 0x02, // -4.6V 0x84, // AUTO mode ST7735_PWCTR2 , 1 , // 8: Power control, 1 arg, no delay: 0xC5, // VGH25 = 2.4C VGSEL = -10 VGH = 3 * AVDD ST7735_PWCTR3 , 2 , // 9: Power control, 2 args, no delay: 0x0A, // Opamp current small 0x00, // Boost frequency ST7735_PWCTR4 , 2 , // 10: Power control, 2 args, no delay: 0x8A, // BCLK/2, Opamp current small & Medium low 0x2A, ST7735_PWCTR5 , 2 , // 11: Power control, 2 args, no delay: 0x8A, 0xEE, ST7735_VMCTR1 , 1 , // 12: Power control, 1 arg, no delay: 0x0E, ST7735_INVOFF , 0 , // 13: Don't invert display, no args, no delay ST7735_MADCTL , 1 , // 14: Memory access control (directions), 1 arg: 0xC8, // row addr/col addr, bottom to top refresh ST7735_COLMOD , 1 , // 15: set color mode, 1 arg, no delay: 0x05 }; // 16-bit color static const uint8_t Rcmd2green[] = { // Init for 7735R, part 2 (green tab only) 2, // 2 commands in list: ST7735_CASET , 4 , // 1: Column addr set, 4 args, no delay: 0x00, 0x02, // XSTART = 0 0x00, 0x7F+0x02, // XEND = 127 ST7735_RASET , 4 , // 2: Row addr set, 4 args, no delay: 0x00, 0x01, // XSTART = 0 0x00, 0x9F+0x01 }; // XEND = 159 static const uint8_t Rcmd2red[] = { // Init for 7735R, part 2 (red tab only) 2, // 2 commands in list: ST7735_CASET , 4 , // 1: Column addr set, 4 args, no delay: 0x00, 0x00, // XSTART = 0 0x00, 0x7F, // XEND = 127 ST7735_RASET , 4 , // 2: Row addr set, 4 args, no delay: 0x00, 0x00, // XSTART = 0 0x00, 0x9F }; // XEND = 159 static const uint8_t Rcmd3[] = { // Init for 7735R, part 3 (red or green tab) 4, // 4 commands in list: ST7735_GMCTRP1, 16 , // 1: Magical unicorn dust, 16 args, no delay: 0x02, 0x1c, 0x07, 0x12, 0x37, 0x32, 0x29, 0x2d, 0x29, 0x25, 0x2B, 0x39, 0x00, 0x01, 0x03, 0x10, ST7735_GMCTRN1, 16 , // 2: Sparkles and rainbows, 16 args, no delay: 0x03, 0x1d, 0x07, 0x06, 0x2E, 0x2C, 0x29, 0x2D, 0x2E, 0x2E, 0x37, 0x3F, 0x00, 0x00, 0x02, 0x10, ST7735_NORON , DELAY, // 3: Normal display on, no args, w/delay 10, // 10 ms delay ST7735_DISPON , DELAY, // 4: Main screen turn on, no args w/delay 100 }; // 100 ms delay // Companion code to the above tables. Reads and issues // a series of LCD commands stored in ROM byte array. void static commandList(const uint8_t *addr) { uint8_t numCommands, numArgs; uint16_t ms; numCommands = *(addr++); // Number of commands to follow while(numCommands--) { // For each command... writecommand(*(addr++)); // Read, issue command numArgs = *(addr++); // Number of args to follow ms = numArgs & DELAY; // If hibit set, delay follows args numArgs &= ~DELAY; // Mask out delay bit while(numArgs--) { // For each argument... writedata(*(addr++)); // Read, issue argument } if(ms) { ms = *(addr++); // Read post-command delay time (ms) if(ms == 255) ms = 500; // If 255, delay for 500 ms Delay1ms(ms); } } } // Initialization code common to both 'B' and 'R' type displays void static commonInit(const uint8_t *cmdList) { ColStart = RowStart = 0; // May be overridden in init func // activate clock for Port A SYSCTL_RCGCGPIO_R |= SYSCTL_RCGCGPIO_R0; // allow time for clock to stabilize while((SYSCTL_PRGPIO_R&SYSCTL_PRGPIO_R0) == 0){}; // activate clock for SSI0 SYSCTL_RCGCSSI_R |= SYSCTL_RCGCSSI_R0; // allow time for clock to stabilize while((SYSCTL_PRSSI_R&SYSCTL_PRSSI_R0) == 0){}; // toggle RST low to reset; CS low so it'll listen to us // SSI0Fss is used as GPIO GPIO_PORTA_DIR_R |= 0xC8; // make PA3,6,7 out GPIO_PORTA_AFSEL_R &= ~0xC8; // disable alt funct on PA3,6,7 GPIO_PORTA_DEN_R |= 0xC8; // enable digital I/O on PA3,6,7 // configure PA3,6,7 as GPIO GPIO_PORTA_PCTL_R = (GPIO_PORTA_PCTL_R&0x00FF0FFF)+0x00000000; GPIO_PORTA_AMSEL_R &= ~0xC8; // disable analog functionality on PA3,6,7 TFT_CS = TFT_CS_LOW; RESET = RESET_HIGH; Delay1ms(500); RESET = RESET_LOW; Delay1ms(500); RESET = RESET_HIGH; Delay1ms(500); // initialize SSI0 GPIO_PORTA_AFSEL_R |= 0x34; // enable alt funct on PA2,4,5 GPIO_PORTA_PUR_R |= 0x3C; // enable weak pullup on PA2,3,4,5 GPIO_PORTA_DEN_R |= 0x34; // enable digital I/O on PA2,4,5 // configure PA2,4,5 as SSI GPIO_PORTA_PCTL_R = (GPIO_PORTA_PCTL_R&0xFF00F0FF)+0x00220200; GPIO_PORTA_AMSEL_R &= ~0x34; // disable analog functionality on PA2,4,5 SDC_CS_Init(); // SDC CS on PB0 or PD7 SDC_CS = SDC_CS_HIGH; SSI0_CR1_R &= ~SSI_CR1_SSE; // disable SSI SSI0_CR1_R &= ~SSI_CR1_MS; // master mode // configure for clock from source PIOSC for baud clock source SSI0_CC_R = (SSI0_CC_R&~SSI_CC_CS_M)+SSI_CC_CS_PIOSC; // clock divider for 8 MHz SSIClk (16 MHz PIOSC/2) // PIOSC/(CPSDVSR*(1+SCR)) // 16/(2*(1+0)) = 8 MHz SSI0_CPSR_R = (SSI0_CPSR_R&~SSI_CPSR_CPSDVSR_M)+2; // must be even number SSI0_CR0_R &= ~(SSI_CR0_SCR_M | // SCR = 0 (8 Mbps data rate) SSI_CR0_SPH | // SPH = 0 SSI_CR0_SPO); // SPO = 0 // FRF = Freescale format SSI0_CR0_R = (SSI0_CR0_R&~SSI_CR0_FRF_M)+SSI_CR0_FRF_MOTO; // DSS = 8-bit data SSI0_CR0_R = (SSI0_CR0_R&~SSI_CR0_DSS_M)+SSI_CR0_DSS_8; SSI0_CR1_R |= SSI_CR1_SSE; // enable SSI if(cmdList) commandList(cmdList); } //------------ST7735_InitB------------ // Initialization for ST7735B screens. // Input: none // Output: none void ST7735_InitB(void) { commonInit(Bcmd); ST7735_SetCursor(0,0); StTextColor = ST7735_YELLOW; ST7735_FillScreen(0); // set screen to black } //------------ST7735_InitR------------ // Initialization for ST7735R screens (green or red tabs). // Input: option one of the enumerated options depending on tabs // Output: none void ST7735_InitR(enum initRFlags option) { commonInit(Rcmd1); if(option == INITR_GREENTAB) { commandList(Rcmd2green); ColStart = 2; RowStart = 1; } else { // colstart, rowstart left at default '0' values commandList(Rcmd2red); } commandList(Rcmd3); // if black, change MADCTL color filter if (option == INITR_BLACKTAB) { writecommand(ST7735_MADCTL); writedata(0xC0); } TabColor = option; ST7735_SetCursor(0,0); StTextColor = ST7735_YELLOW; ST7735_FillScreen(0); // set screen to black } // Set the region of the screen RAM to be modified // Pixel colors are sent left to right, top to bottom // (same as Font table is encoded; different from regular bitmap) // Requires 11 bytes of transmission void static setAddrWindow(uint8_t x0, uint8_t y0, uint8_t x1, uint8_t y1) { writecommand(ST7735_CASET); // Column addr set writedata(0x00); writedata(x0+ColStart); // XSTART writedata(0x00); writedata(x1+ColStart); // XEND writecommand(ST7735_RASET); // Row addr set writedata(0x00); writedata(y0+RowStart); // YSTART writedata(0x00); writedata(y1+RowStart); // YEND writecommand(ST7735_RAMWR); // write to RAM } // Send two bytes of data, most significant byte first // Requires 2 bytes of transmission void static pushColor(uint16_t color) { writedata((uint8_t)(color >> 8)); writedata((uint8_t)color); } //------------ST7735_DrawPixel------------ // Color the pixel at the given coordinates with the given color. // Requires 13 bytes of transmission // Input: x horizontal position of the pixel, columns from the left edge // must be less than 128 // 0 is on the left, 126 is near the right // y vertical position of the pixel, rows from the top edge // must be less than 160 // 159 is near the wires, 0 is the side opposite the wires // color 16-bit color, which can be produced by ST7735_Color565() // Output: none void ST7735_DrawPixel(int16_t x, int16_t y, uint16_t color) { if((x < 0) || (x >= _width) || (y < 0) || (y >= _height)) return; // setAddrWindow(x,y,x+1,y+1); // original code, bug??? setAddrWindow(x,y,x,y); pushColor(color); deselect(); } //------------ST7735_DrawFastVLine------------ // Draw a vertical line at the given coordinates with the given height and color. // A vertical line is parallel to the longer side of the rectangular display // Requires (11 + 2*h) bytes of transmission (assuming image fully on screen) // Input: x horizontal position of the start of the line, columns from the left edge // y vertical position of the start of the line, rows from the top edge // h vertical height of the line // color 16-bit color, which can be produced by ST7735_Color565() // Output: none void ST7735_DrawFastVLine(int16_t x, int16_t y, int16_t h, uint16_t color) { uint8_t hi = color >> 8, lo = color; // Rudimentary clipping if((x >= _width) || (y >= _height)) return; if((y+h-1) >= _height) h = _height-y; setAddrWindow(x, y, x, y+h-1); while (h--) { writedata(hi); writedata(lo); } deselect(); } //------------ST7735_DrawFastHLine------------ // Draw a horizontal line at the given coordinates with the given width and color. // A horizontal line is parallel to the shorter side of the rectangular display // Requires (11 + 2*w) bytes of transmission (assuming image fully on screen) // Input: x horizontal position of the start of the line, columns from the left edge // y vertical position of the start of the line, rows from the top edge // w horizontal width of the line // color 16-bit color, which can be produced by ST7735_Color565() // Output: none void ST7735_DrawFastHLine(int16_t x, int16_t y, int16_t w, uint16_t color) { uint8_t hi = color >> 8, lo = color; // Rudimentary clipping if((x >= _width) || (y >= _height)) return; if((x+w-1) >= _width) w = _width-x; setAddrWindow(x, y, x+w-1, y); while (w--) { writedata(hi); writedata(lo); } deselect(); } //------------ST7735_FillScreen------------ // Fill the screen with the given color. // Requires 40,971 bytes of transmission // Input: color 16-bit color, which can be produced by ST7735_Color565() // Output: none void ST7735_FillScreen(uint16_t color) { ST7735_FillRect(0, 0, _width, _height, color); // original // screen is actually 129 by 161 pixels, x 0 to 128, y goes from 0 to 160 } //------------ST7735_FillRect------------ // Draw a filled rectangle at the given coordinates with the given width, height, and color. // Requires (11 + 2*w*h) bytes of transmission (assuming image fully on screen) // Input: x horizontal position of the top left corner of the rectangle, columns from the left edge // y vertical position of the top left corner of the rectangle, rows from the top edge // w horizontal width of the rectangle // h vertical height of the rectangle // color 16-bit color, which can be produced by ST7735_Color565() // Output: none void ST7735_FillRect(int16_t x, int16_t y, int16_t w, int16_t h, uint16_t color) { uint8_t hi = color >> 8, lo = color; // rudimentary clipping (drawChar w/big text requires this) if((x >= _width) || (y >= _height)) return; if((x + w - 1) >= _width) w = _width - x; if((y + h - 1) >= _height) h = _height - y; setAddrWindow(x, y, x+w-1, y+h-1); for(y=h; y>0; y--) { for(x=w; x>0; x--) { writedata(hi); writedata(lo); } } deselect(); } //------------ST7735_DrawSmallCircle------------ // Draw a small circle (diameter of 6 pixels) // rectangle at the given coordinates with the given color. // Requires (11*6+24*2)=114 bytes of transmission (assuming image on screen) // Input: x horizontal position of the top left corner of the circle, columns from the left edge // y vertical position of the top left corner of the circle, rows from the top edge // color 16-bit color, which can be produced by ST7735_Color565() // Output: none int16_t const smallCircle[6][3]={ {2,3, 2}, {1 , 4, 4}, {0 , 5, 6}, {0 , 5, 6}, {1 , 4, 4}, {2,3, 2}}; void ST7735_DrawSmallCircle(int16_t x, int16_t y, uint16_t color) { uint32_t i,w; uint8_t hi = color >> 8, lo = color; // rudimentary clipping if((x>_width-5)||(y>_height-5)) return; // doesn't fit for(i=0; i<6; i++){ setAddrWindow(x+smallCircle[i][0], y+i, x+smallCircle[i][1], y+i); w = smallCircle[i][2]; while (w--) { writedata(hi); writedata(lo); } } deselect(); } //------------ST7735_DrawCircle------------ // Draw a small circle (diameter of 10 pixels) // rectangle at the given coordinates with the given color. // Requires (11*10+68*2)=178 bytes of transmission (assuming image on screen) // Input: x horizontal position of the top left corner of the circle, columns from the left edge // y vertical position of the top left corner of the circle, rows from the top edge // color 16-bit color, which can be produced by ST7735_Color565() // Output: none int16_t const circle[10][3]={ { 4,5, 2}, {2 , 7, 6}, {1 , 8, 8}, {1 , 8, 8}, {0 , 9, 10}, {0 , 9, 10}, {1 , 8, 8}, {1 , 8, 8}, {2 , 7, 6}, { 4,5, 2}}; void ST7735_DrawCircle(int16_t x, int16_t y, uint16_t color) { uint32_t i,w; uint8_t hi = color >> 8, lo = color; // rudimentary clipping if((x>_width-9)||(y>_height-9)) return; // doesn't fit for(i=0; i<10; i++){ setAddrWindow(x+circle[i][0], y+i, x+circle[i][1], y+i); w = circle[i][2]; while (w--) { writedata(hi); writedata(lo); } } deselect(); } //------------ST7735_Color565------------ // Pass 8-bit (each) R,G,B and get back 16-bit packed color. // Input: r red value // g green value // b blue value // Output: 16-bit color uint16_t ST7735_Color565(uint8_t r, uint8_t g, uint8_t b) { return ((b & 0xF8) << 8) | ((g & 0xFC) << 3) | (r >> 3); } //------------ST7735_SwapColor------------ // Swaps the red and blue values of the given 16-bit packed color; // green is unchanged. // Input: x 16-bit color in format B, G, R // Output: 16-bit color in format R, G, B uint16_t ST7735_SwapColor(uint16_t x) { return (x << 11) | (x & 0x07E0) | (x >> 11); } //------------ST7735_DrawBitmap------------ // Displays a 16-bit color BMP image. A bitmap file that is created // by a PC image processing program has a header and may be padded // with dummy columns so the data have four byte alignment. This // function assumes that all of that has been stripped out, and the // array image[] has one 16-bit halfword for each pixel to be // displayed on the screen (encoded in reverse order, which is // standard for bitmap files). An array can be created in this // format from a 24-bit-per-pixel .bmp file using the associated // converter program. // (x,y) is the screen location of the lower left corner of BMP image // Requires (11 + 2*w*h) bytes of transmission (assuming image fully on screen) // Input: x horizontal position of the bottom left corner of the image, columns from the left edge // y vertical position of the bottom left corner of the image, rows from the top edge // image pointer to a 16-bit color BMP image // w number of pixels wide // h number of pixels tall // Output: none // Must be less than or equal to 128 pixels wide by 160 pixels high void ST7735_DrawBitmap(int16_t x, int16_t y, const uint16_t *image, int16_t w, int16_t h){ int16_t skipC = 0; // non-zero if columns need to be skipped due to clipping int16_t originalWidth = w; // save this value; even if not all columns fit on the screen, the image is still this width in ROM int i = w*(h - 1); if((x >= _width) || ((y - h + 1) >= _height) || ((x + w) <= 0) || (y < 0)){ return; // image is totally off the screen, do nothing } if((w > _width) || (h > _height)){ // image is too wide for the screen, do nothing //***This isn't necessarily a fatal error, but it makes the //following logic much more complicated, since you can have //an image that exceeds multiple boundaries and needs to be //clipped on more than one side. return; } if((x + w - 1) >= _width){ // image exceeds right of screen skipC = (x + w) - _width; // skip cut off columns w = _width - x; } if((y - h + 1) < 0){ // image exceeds top of screen i = i - (h - y - 1)*originalWidth; // skip the last cut off rows h = y + 1; } if(x < 0){ // image exceeds left of screen w = w + x; skipC = -1*x; // skip cut off columns i = i - x; // skip the first cut off columns x = 0; } if(y >= _height){ // image exceeds bottom of screen h = h - (y - _height + 1); y = _height - 1; } setAddrWindow(x, y-h+1, x+w-1, y); for(y=0; y> 8)); // send the bottom 8 bits writedata((uint8_t)image[i]); i = i + 1; // go to the next pixel } i = i + skipC; i = i - 2*originalWidth; } deselect(); } //------------ST7735_DrawCharS------------ // Simple character draw function. This is the same function from // Adafruit_GFX.c but adapted for this processor. However, each call // to ST7735_DrawPixel() calls setAddrWindow(), which needs to send // many extra data and commands. If the background color is the same // as the text color, no background will be printed, and text can be // drawn right over existing images without covering them with a box. // Requires (11 + 2*size*size)*6*8 (image fully on screen; textcolor != bgColor) // Input: x horizontal position of the top left corner of the character, columns from the left edge // y vertical position of the top left corner of the character, rows from the top edge // c character to be printed // textColor 16-bit color of the character // bgColor 16-bit color of the background // size number of pixels per character pixel (e.g. size==2 prints each pixel of font as 2x2 square) // Output: none void ST7735_DrawCharS(int16_t x, int16_t y, char c, int16_t textColor, int16_t bgColor, uint8_t size){ uint8_t line; // vertical column of pixels of character in font int32_t i, j; if((x >= _width) || // Clip right (y >= _height) || // Clip bottom ((x + 6 * size - 1) < 0) || // Clip left ((y + 8 * size - 1) < 0)) // Clip top return; for (i=0; i<6; i++ ) { if (i == 5) line = 0x0; else line = Font[(c*5)+i]; for (j = 0; j<8; j++) { if (line & 0x1) { if (size == 1) // default size ST7735_DrawPixel(x+i, y+j, textColor); else { // big size ST7735_FillRect(x+(i*size), y+(j*size), size, size, textColor); } } else if (bgColor != textColor) { if (size == 1) // default size ST7735_DrawPixel(x+i, y+j, bgColor); else { // big size ST7735_FillRect(x+i*size, y+j*size, size, size, bgColor); } } line >>= 1; } } } //------------ST7735_DrawChar------------ // Advanced character draw function. This is similar to the function // from Adafruit_GFX.c but adapted for this processor. However, this // function only uses one call to setAddrWindow(), which allows it to // run at least twice as fast. // Requires (11 + size*size*6*8) bytes of transmission (assuming image fully on screen) // Input: x horizontal position of the top left corner of the character, columns from the left edge // y vertical position of the top left corner of the character, rows from the top edge // c character to be printed // textColor 16-bit color of the character // bgColor 16-bit color of the background // size number of pixels per character pixel (e.g. size==2 prints each pixel of font as 2x2 square) // Output: none void ST7735_DrawChar(int16_t x, int16_t y, char c, int16_t textColor, int16_t bgColor, uint8_t size){ uint8_t line; // horizontal row of pixels of character int32_t col, row, i, j;// loop indices if(((x + 6*size - 1) >= _width) || // Clip right ((y + 8*size - 1) >= _height) || // Clip bottom ((x + 6*size - 1) < 0) || // Clip left ((y + 8*size - 1) < 0)){ // Clip top return; } setAddrWindow(x, y, x+6*size-1, y+8*size-1); line = 0x01; // print the top row first // print the rows, starting at the top for(row=0; row<8; row=row+1){ for(i=0; i15) return 0; while(*pt){ ST7735_DrawCharS(x*6, y*10, *pt, textColor, ST7735_BLACK, 1); pt++; x = x+1; if(x>20) return count; // number of characters printed count++; } return count; // number of characters printed } //-----------------------fillmessage----------------------- // Output a 32-bit number in unsigned decimal format // Input: 32-bit number to be transferred // Output: none // Variable format 1-10 digits with no space before or after char Message[12]; uint32_t Messageindex; void fillmessage(uint32_t n){ // This function uses recursion to convert decimal number // of unspecified length as an ASCII string if(n >= 10){ fillmessage(n/10); n = n%10; } Message[Messageindex] = (n+'0'); /* n is between 0 and 9 */ if(Messageindex<11)Messageindex++; } //********ST7735_SetCursor***************** // Move the cursor to the desired X- and Y-position. The // next character will be printed here. X=0 is the leftmost // column. Y=0 is the top row. // inputs: newX new X-position of the cursor (0<=newX<=20) // newY new Y-position of the cursor (0<=newY<=15) // outputs: none void ST7735_SetCursor(uint32_t newX, uint32_t newY){ if((newX > 20) || (newY > 15)){ // bad input return; // do nothing } StX = newX; StY = newY; } //-----------------------ST7735_OutUDec----------------------- // Output a 32-bit number in unsigned decimal format // Position determined by ST7735_SetCursor command // Color set by ST7735_SetTextColor // Input: 32-bit number to be transferred // Output: none // Variable format 1-10 digits with no space before or after void ST7735_OutUDec(uint32_t n){ Messageindex = 0; fillmessage(n); Message[Messageindex] = 0; // terminate ST7735_DrawString(StX,StY,Message,StTextColor); StX = StX+Messageindex; if(StX>20){ StX = 20; ST7735_DrawCharS(StX*6,StY*10,'*',ST7735_RED,ST7735_BLACK, 1); } } #define MADCTL_MY 0x80 #define MADCTL_MX 0x40 #define MADCTL_MV 0x20 #define MADCTL_ML 0x10 #define MADCTL_RGB 0x00 #define MADCTL_BGR 0x08 #define MADCTL_MH 0x04 //------------ST7735_SetRotation------------ // Change the image rotation. // Requires 2 bytes of transmission // Input: m new rotation value (0 to 3) // Output: none void ST7735_SetRotation(uint8_t m) { writecommand(ST7735_MADCTL); Rotation = m % 4; // can't be higher than 3 switch (Rotation) { case 0: if (TabColor == INITR_BLACKTAB) { writedata(MADCTL_MX | MADCTL_MY | MADCTL_RGB); } else { writedata(MADCTL_MX | MADCTL_MY | MADCTL_BGR); } _width = ST7735_TFTWIDTH; _height = ST7735_TFTHEIGHT; break; case 1: if (TabColor == INITR_BLACKTAB) { writedata(MADCTL_MY | MADCTL_MV | MADCTL_RGB); } else { writedata(MADCTL_MY | MADCTL_MV | MADCTL_BGR); } _width = ST7735_TFTHEIGHT; _height = ST7735_TFTWIDTH; break; case 2: if (TabColor == INITR_BLACKTAB) { writedata(MADCTL_RGB); } else { writedata(MADCTL_BGR); } _width = ST7735_TFTWIDTH; _height = ST7735_TFTHEIGHT; break; case 3: if (TabColor == INITR_BLACKTAB) { writedata(MADCTL_MX | MADCTL_MV | MADCTL_RGB); } else { writedata(MADCTL_MX | MADCTL_MV | MADCTL_BGR); } _width = ST7735_TFTHEIGHT; _height = ST7735_TFTWIDTH; break; } deselect(); } //------------ST7735_InvertDisplay------------ // Send the command to invert all of the colors. // Requires 1 byte of transmission // Input: i 0 to disable inversion; non-zero to enable inversion // Output: none void ST7735_InvertDisplay(int i) { if(i){ writecommand(ST7735_INVON); } else{ writecommand(ST7735_INVOFF); } deselect(); } // graphics routines // y coordinates 0 to 31 used for labels and messages // y coordinates 32 to 159 128 pixels high // x coordinates 0 to 127 128 pixels wide int32_t Ymax,Ymin,X; // X goes from 0 to 127 int32_t Yrange; //YrangeDiv2; // *************** ST7735_PlotClear ******************** // Clear the graphics buffer, set X coordinate to 0 // This routine clears the display // Inputs: ymin and ymax are range of the plot // Outputs: none void ST7735_PlotClear(int32_t ymin, int32_t ymax){ ST7735_FillRect(0, 32, 128, 128, ST7735_Color565(228,228,228)); // light grey if(ymax>ymin){ Ymax = ymax; Ymin = ymin; Yrange = ymax-ymin; } else{ Ymax = ymin; Ymin = ymax; Yrange = ymax-ymin; } //YrangeDiv2 = Yrange/2; X = 0; } // *************** ST7735_PlotPoint ******************** // Used in the voltage versus time plot, plot one point at y // It does output to display // Inputs: y is the y coordinate of the point plotted // Outputs: none void ST7735_PlotPoint(int32_t y){int32_t j; if(yYmax) y=Ymax; // X goes from 0 to 127 // j goes from 159 to 32 // y=Ymax maps to j=32 // y=Ymin maps to j=159 j = 32+(127*(Ymax-y))/Yrange; if(j<32) j = 32; if(j>159) j = 159; ST7735_DrawPixel(X, j, ST7735_BLUE); ST7735_DrawPixel(X+1, j, ST7735_BLUE); ST7735_DrawPixel(X, j+1, ST7735_BLUE); ST7735_DrawPixel(X+1, j+1, ST7735_BLUE); } // *************** ST7735_PlotLine ******************** // Used in the voltage versus time plot, plot line to new point // It does output to display // Inputs: y is the y coordinate of the point plotted // Outputs: none int32_t lastj=0; void ST7735_PlotLine(int32_t y){int32_t i,j; if(yYmax) y=Ymax; // X goes from 0 to 127 // j goes from 159 to 32 // y=Ymax maps to j=32 // y=Ymin maps to j=159 j = 32+(127*(Ymax-y))/Yrange; if(j < 32) j = 32; if(j > 159) j = 159; if(lastj < 32) lastj = j; if(lastj > 159) lastj = j; if(lastj < j){ for(i = lastj+1; i<=j ; i++){ ST7735_DrawPixel(X, i, ST7735_BLUE) ; ST7735_DrawPixel(X+1, i, ST7735_BLUE) ; } }else if(lastj > j){ for(i = j; iYmax) y1=Ymax; // X goes from 0 to 127 // j goes from 159 to 32 // y=Ymax maps to j=32 // y=Ymin maps to j=159 j = 32+(127*(Ymax-y1))/Yrange; if(j<32) j = 32; if(j>159) j = 159; ST7735_DrawPixel(X, j, ST7735_BLUE); if(y2Ymax) y2=Ymax; j = 32+(127*(Ymax-y2))/Yrange; if(j<32) j = 32; if(j>159) j = 159; ST7735_DrawPixel(X, j, ST7735_BLACK); } // *************** ST7735_PlotBar ******************** // Used in the voltage versus time bar, plot one bar at y // It does not output to display until RIT128x96x4ShowPlot called // Inputs: y is the y coordinate of the bar plotted // Outputs: none void ST7735_PlotBar(int32_t y){ int32_t j; if(yYmax) y=Ymax; // X goes from 0 to 127 // j goes from 159 to 32 // y=Ymax maps to j=32 // y=Ymin maps to j=159 j = 32+(127*(Ymax-y))/Yrange; ST7735_DrawFastVLine(X, j, 159-j, ST7735_BLACK); } // full scaled defined as 3V // Input is 0 to 511, 0 => 159 and 511 => 32 uint8_t const dBfs[512]={ 159, 159, 145, 137, 131, 126, 123, 119, 117, 114, 112, 110, 108, 107, 105, 104, 103, 101, 100, 99, 98, 97, 96, 95, 94, 93, 93, 92, 91, 90, 90, 89, 88, 88, 87, 87, 86, 85, 85, 84, 84, 83, 83, 82, 82, 81, 81, 81, 80, 80, 79, 79, 79, 78, 78, 77, 77, 77, 76, 76, 76, 75, 75, 75, 74, 74, 74, 73, 73, 73, 72, 72, 72, 72, 71, 71, 71, 71, 70, 70, 70, 70, 69, 69, 69, 69, 68, 68, 68, 68, 67, 67, 67, 67, 66, 66, 66, 66, 66, 65, 65, 65, 65, 65, 64, 64, 64, 64, 64, 63, 63, 63, 63, 63, 63, 62, 62, 62, 62, 62, 62, 61, 61, 61, 61, 61, 61, 60, 60, 60, 60, 60, 60, 59, 59, 59, 59, 59, 59, 59, 58, 58, 58, 58, 58, 58, 58, 57, 57, 57, 57, 57, 57, 57, 56, 56, 56, 56, 56, 56, 56, 56, 55, 55, 55, 55, 55, 55, 55, 55, 54, 54, 54, 54, 54, 54, 54, 54, 53, 53, 53, 53, 53, 53, 53, 53, 53, 52, 52, 52, 52, 52, 52, 52, 52, 52, 52, 51, 51, 51, 51, 51, 51, 51, 51, 51, 51, 50, 50, 50, 50, 50, 50, 50, 50, 50, 50, 49, 49, 49, 49, 49, 49, 49, 49, 49, 49, 49, 48, 48, 48, 48, 48, 48, 48, 48, 48, 48, 48, 47, 47, 47, 47, 47, 47, 47, 47, 47, 47, 47, 47, 46, 46, 46, 46, 46, 46, 46, 46, 46, 46, 46, 46, 46, 45, 45, 45, 45, 45, 45, 45, 45, 45, 45, 45, 45, 45, 44, 44, 44, 44, 44, 44, 44, 44, 44, 44, 44, 44, 44, 44, 43, 43, 43, 43, 43, 43, 43, 43, 43, 43, 43, 43, 43, 43, 43, 42, 42, 42, 42, 42, 42, 42, 42, 42, 42, 42, 42, 42, 42, 42, 41, 41, 41, 41, 41, 41, 41, 41, 41, 41, 41, 41, 41, 41, 41, 41, 40, 40, 40, 40, 40, 40, 40, 40, 40, 40, 40, 40, 40, 40, 40, 40, 40, 39, 39, 39, 39, 39, 39, 39, 39, 39, 39, 39, 39, 39, 39, 39, 39, 39, 39, 38, 38, 38, 38, 38, 38, 38, 38, 38, 38, 38, 38, 38, 38, 38, 38, 38, 38, 38, 37, 37, 37, 37, 37, 37, 37, 37, 37, 37, 37, 37, 37, 37, 37, 37, 37, 37, 37, 36, 36, 36, 36, 36, 36, 36, 36, 36, 36, 36, 36, 36, 36, 36, 36, 36, 36, 36, 36, 36, 35, 35, 35, 35, 35, 35, 35, 35, 35, 35, 35, 35, 35, 35, 35, 35, 35, 35, 35, 35, 35, 34, 34, 34, 34, 34, 34, 34, 34, 34, 34, 34, 34, 34, 34, 34, 34, 34, 34, 34, 34, 34, 34, 34, 33, 33, 33, 33, 33, 33, 33, 33, 33, 33, 33, 33, 33, 33, 33, 33, 33, 33, 33, 33, 33, 33, 33, 33, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32 }; // *************** ST7735_PlotdBfs ******************** // Used in the amplitude versus frequency plot, plot bar point at y // 0 to 0.625V scaled on a log plot from min to max // It does output to display // Inputs: y is the y ADC value of the bar plotted // Outputs: none void ST7735_PlotdBfs(int32_t y){ int32_t j; y = y/2; // 0 to 2047 if(y<0) y=0; if(y>511) y=511; // X goes from 0 to 127 // j goes from 159 to 32 // y=511 maps to j=32 // y=0 maps to j=159 j = dBfs[y]; ST7735_DrawFastVLine(X, j, 159-j, ST7735_BLACK); } // *************** ST7735_PlotNext ******************** // Used in all the plots to step the X coordinate one pixel // X steps from 0 to 127, then back to 0 again // It does not output to display // Inputs: none // Outputs: none void ST7735_PlotNext(void){ if(X==127){ X = 0; } else{ X++; } } // *************** ST7735_PlotNextErase ******************** // Used in all the plots to step the X coordinate one pixel // X steps from 0 to 127, then back to 0 again // It clears the vertical space into which the next pixel will be drawn // Inputs: none // Outputs: none void ST7735_PlotNextErase(void){ if(X==127){ X = 0; } else{ X++; } ST7735_DrawFastVLine(X,32,128,ST7735_Color565(228,228,228)); } // Used in all the plots to write buffer to LCD // Example 1 Voltage versus time // ST7735_PlotClear(0,4095); // range from 0 to 4095 // ST7735_PlotPoint(data); ST7735_PlotNext(); // called 128 times // Example 2a Voltage versus time (N data points/pixel, time scale) // ST7735_PlotClear(0,4095); // range from 0 to 4095 // { for(j=0;j15){ StY = 0; } ST7735_DrawString(0,StY," ",StTextColor); return; } ST7735_DrawCharS(StX*6,StY*10,ch,ST7735_YELLOW,ST7735_BLACK, 1); StX++; if(StX>20){ StX = 20; ST7735_DrawCharS(StX*6,StY*10,'*',ST7735_RED,ST7735_BLACK, 1); } return; } //********ST7735_OutString***************** // Print a string of characters to the ST7735 LCD. // Position determined by ST7735_SetCursor command // Color set by ST7735_SetTextColor // The string will not automatically wrap. // inputs: ptr pointer to NULL-terminated ASCII string // outputs: none void ST7735_OutString(char *ptr){ while(*ptr){ ST7735_OutChar(*ptr); ptr = ptr + 1; } } // ************** ST7735_SetTextColor ************************ // Sets the color in which the characters will be printed // Background color is fixed at black // Input: 16-bit packed color // Output: none // ******************************************************** void ST7735_SetTextColor(uint16_t color){ StTextColor = color; } // *************** Output_Init ******************** // Standard device driver initialization function for printf // Initialize ST7735 LCD // Inputs: none // Outputs: none void Output_Init(void){ ST7735_InitR(INITR_REDTAB); ST7735_FillScreen(0); // set screen to black } // Clear display void Output_Clear(void){ // Clears the display ST7735_FillScreen(0); // set screen to black } // Turn off display (low power) void Output_Off(void){ // Turns off the display Output_Clear(); // not implemented } // Turn on display void Output_On(void){ // Turns on the display Output_Init(); // reinitialize } // set the color for future output // Background color is fixed at black // Input: 16-bit packed color // Output: none void Output_Color(uint32_t newColor){ // Set color of future output ST7735_SetTextColor(newColor); }