+/rtos

git clone https://git.julia.blue/+/rtos

Vivek MalneediMerge branch 'master' of github.com:EE445M-Sp20/lab-6-vm22967_jbr2558021d2d4

master
3.4 KiB96 linesraw
1#include <stdint.h>
2
3// Backlight (pin 10) connected to +3.3 V
4// MISO (pin 9) connected to PA4 (SSI0Rx)
5// SCK (pin 8) connected to PA2 (SSI0Clk)
6// MOSI (pin 7) connected to PA5 (SSI0Tx)
7// TFT_CS (pin 6) connected to PA3 (SSI0Fss) <- GPIO high to disable TFT
8// CARD_CS (pin 5) connected to PB0 GPIO output
9// Data/Command (pin 4) connected to PA6 (GPIO)<- GPIO low not using TFT
10// RESET (pin 3) connected to PA7 (GPIO)<- GPIO high to disable TFT
11// VCC (pin 2) connected to +3.3 V
12// Gnd (pin 1) connected to ground
13
14typedef enum {
15    STA_OK = 0,
16    STA_NOINIT = 1,  // Drive not initialized
17    STA_NODISK = 2,  // No medium in the drive
18    STA_PROTECT = 4, // Write protected
19} DSTATUS;
20
21// Results of Disk Functions
22typedef enum {
23    RES_OK = 0, // 0: Successful
24    RES_ERROR,  // 1: R/W Error
25    RES_WRPRT,  // 2: Write Protected
26    RES_NOTRDY, // 3: Not Ready
27    RES_PARERR  // 4: Invalid Parameter
28} DRESULT;
29
30// Initialize the interface to the SD card
31// Since this program initializes the disk, it must run with the disk periodic
32// task operating.
33DSTATUS eDisk_Init();
34
35// Checks the status of the card
36DSTATUS eDisk_Status();
37
38// Read data from the SD card
39// count: number of sectors to read (1..255)
40DRESULT eDisk_Read(uint8_t* buff, uint32_t sector, uint8_t count);
41
42// Read 512-byte block from SD card
43DRESULT eDisk_ReadBlock(void* buff, uint32_t sector);
44
45// Write bytes to SD card.
46// count: number of sectors to write (1..255)
47DRESULT eDisk_Write(const uint8_t* buff, uint32_t sector, uint8_t count);
48
49// Write one block to the SD card  (read to RAM)
50DRESULT eDisk_WriteBlock(const void* buff, uint32_t sector);
51
52void SSI0_Init(unsigned long CPSDVSR);
53
54// This implements timeout functions (should be called every ms)
55void disk_timerproc(void);
56
57// General purpose function for all disk I/O
58DRESULT disk_ioctl(uint8_t cmd, void* buff);
59
60// Command codes for disk_ioctrl fucntion:
61
62// Generic command
63#define CTRL_SYNC                                                              \
64    0 // Complete pending write process (needed at _FS_READONLY == 0)
65#define GET_SECTOR_COUNT 1 // Get media size (needed at _USE_MKFS == 1)
66#define GET_SECTOR_SIZE 2  // Get sector size (needed at _MAX_SS != _MIN_SS)
67#define GET_BLOCK_SIZE 3   // Get erase block size (needed at _USE_MKFS == 1)
68#define CTRL_TRIM                                                              \
69    4 // Inform device that the data on the block of sectors is no longer used
70
71// Generic command
72#define CTRL_FORMAT 5     // Create physical format on the media
73#define CTRL_POWER_IDLE 6 // Put the device idle state
74#define CTRL_POWER_OFF 7  // Put the device off state
75#define CTRL_LOCK 8       // Lock media removal
76#define CTRL_UNLOCK 9     // Unlock media removal
77#define CTRL_EJECT 10     // Eject media
78
79// MMC/SDC specific command
80#define MMC_GET_TYPE 50   // Get card type
81#define MMC_GET_CSD 51    // Get CSD
82#define MMC_GET_CID 52    // Get CID
83#define MMC_GET_OCR 53    // Get OCR
84#define MMC_GET_SDSTAT 54 // Get SD status
85
86// ATA/CF specific command
87#define ATA_GET_REV 60   // Get F/W revision
88#define ATA_GET_MODEL 61 // Get model name
89#define ATA_GET_SN 62    // Get serial number
90
91// MMC card type flags (MMC_GET_TYPE)
92#define CT_MMC 0x01              // MMC ver 3
93#define CT_SD1 0x02              // SD ver 1
94#define CT_SD2 0x04              // SD ver 2
95#define CT_SDC (CT_SD1 | CT_SD2) // SD
96#define CT_BLOCK 0x08            // Block addressing